摘要本文熔炼了Mg-3Sn-2Al-1Zn-0。6Nd和Mg-3Sn-2Al-1Zn两种成分的镁合金,并对其作了固溶和时效两种热处理。用金相显微镜观察了合金的形貌,用摩擦磨损仪测试了材料的摩擦磨损性能,用维氏硬度计测试了材料的显微硬度。用激光共聚焦显微镜观测了材料的摩擦磨损三维图。实验结果显示,稀土Nd的加入在一定程度上改善了材料的摩擦磨损性能,但是稀土镁合金固溶处理并没有明显的提升材料的摩擦磨损性能,原因是铸态合金中Sn元素的本身具有自润滑效果;加入稀土后,Nd和Sn形成新的复杂化合物,材料在增加固溶畸变的同时损失了自润滑,另铸态Mg-3Sn-2Al-1Zn合金易激活非基面滑移,林位错强化非常显著,弱化了合金的第二相强化效果。关于Mg-3Sn-2Al-1Zn和Mg-3Sn-2Al-1Zn-0。6Nd合金固溶、时效工艺仍然需要进一步深入研究。86746

毕业论文关键词:稀土镁合金、摩擦磨损、摩擦系数

Abstract   In this paper, the Mg-3Sn-2Al-1Zn-0。6Nd and Mg-3Sn-2Al-1Zn two components of the magnesium alloy, and made a solid solution and aging of two kinds of heat treatment。 The morphology of the alloy was observed by optical microscope。 The friction and wear properties of the alloy were tested by the friction and wear tester。 The microhardness of the alloy was measured by the Vivtorinox hardness tester。 The friction and wear of the material were observed by laser scanning confocal microscope。 Experimental results show that the Nd join in a certain extent, improve the friction and wear properties, but rare earth magnesium alloy solid solution treatment did not significantly enhance material friction and wear properties, the reason is cast alloys of Sn in itself has a lot of self-lubricating effect; after the addition of rare earth, Nd and Sn formed a new complex compounds, material increase in solid solution distortion at the same time the loss of self lubricating。 Other cast ZK60 alloy Mg-3Sn-2Al-1Zn easy activation of non basal slip, forest dislocation strengthening is very significant, weakening the alloy of second phase strengthening effect。 The solid solution and aging process of Mg-3Sn-2Al-1Zn and Mg-3Sn-2Al-1Zn-0。6Nd alloys still need to be further studied。

Keywords: Rare earth magnesium alloy、Friction and wear、friction coefficient

目录

第一章 绪 论。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。1 

1。1  引  言。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。1

1。2  镁合金的研究现状。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。2

 1。2。1  镁的基本性质 。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。 2

 1。2。2  合金元素在镁合金中作用 。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。 3

上一篇:W元素对TiN薄膜的力学性能及摩擦磨损性能的影响
下一篇:Ti、V元素对Cr-N基薄膜的微观组织力学性能及摩擦性能的影响

3003薄板铝合金高转速搅拌摩擦焊接工艺研究

塑性改善变面轧制AZ31镁合金组织性能演化

6061-T6铝合金静轴肩搅拌摩...

铝合金静轴肩搅拌摩擦焊工艺研究

CoCrCuxFeNiTi0.3高熵合金的摩擦磨损行为

Si含量对TiSiN复合薄膜的微...

微弧氧化-电泳复合沉积制备镁合金生物膜层

从企业eHR建设谈管理信息...

遥感土地用变化监测国内外研究现状

MNL模型历史城区居民活动...

高效课堂教师问卷调查表

大规模MIMO系统的发展研究现状

PCI+PID算法直流力矩电机速...

小型通用机器人控制系统设计任务书

提高小學语文課堂朗读教...

《水浒传》中血腥暴力研...

浅析施工企业保理融资成...