TIG-拉弧复合热源铝合金螺柱焊工艺试验研究
铝合金拉弧式螺柱焊需使用陶瓷套进行保护，通过6061螺柱进行有无惰性气体保护时对焊接接头的影响的试验，通过接头力学性能及微观组织对其进行分析和评价。
本次试验中提出了TIG-拉弧复合热源技术。利用TIG-拉弧复合热源中的TIG电弧可去除铝板表面的氧化膜的同时TIG电弧起到预热的作用,可降低焊接电流,降低热裂纹生成的机率。由于铝板的预热,焊接电流过大时易使飞溅增大,导致出现缺陷的机率增大。24533
毕业论文关键词：铝合金 螺柱焊 TIG焊预热
Title stud welding of aluminum alloy
Abstract
Concerning the problem of that the aluminum alloy is difficult to weld in arc stud welding,the method of arc stud welding of aluminum alloy has been given in this paper.According to analyze the micro configuration and mechanical properties of the welding joint, the effect of the technical parameters would be estimated and the optimal parameter would be got.
The drawn arc stud welding should be protected by the ceramic ring.And the influence of inert gas protection in welding joint would be estimated by analyzing the micro configuration and mechanical properties of the welding joint.
In this paper,the TIG was used to wipe off the oxygenation on the surface of the aluminum alloy.The welding current decreased as the Al board was preheated; also, welding defects were more likely to appear as the welding current got larger and the protection effect was reduced by the splash.
Key word: Aluminum alloy, Stud welding, Tungsten Inert Gas arc Welding
目 次
1 绪论 1
1.1 螺柱焊 1
1.1.1 螺柱焊的基本概述 1
1.1.2 储能式螺柱焊 1
1.1.3 拉弧式螺柱焊 2
1.1.4螺柱焊的特点 2
1.2 铝及铝合金的焊接特点 3
1.3 铝及铝合金的螺柱焊 3
1.3.1 电容式螺柱焊 3
1.3.2 拉弧式螺柱焊 4
1.4 TIG电弧辅助焊接原理 5
2 试验设计 6
2.1 课题研究背景及选题意义 6
2.2 试验设备 6
2.2.1 螺柱焊机 6
2.2.2 TIG焊机 6
2.2.3 力学性能设备 7
2.3 接头金相试样制备 8
2.4 同种材料特种铝螺柱焊接 8
2.4.1 试验材料及处理方法 8
2.4.2 焊接参数及试验设计 9
2.5 异种铝合金螺柱焊接 10
2.5.1试验材料及处理方法 10
2.5.2 焊接参数及试验设计 11
3试验结果及分析 13
3.1 同种材料特种铝螺柱焊接 13
3.1.1 焊接试样外观图 13
3.1.2 焊接试样剪切力学性能试验及分析 16
3.2 异种铝合金螺柱焊接 17
3.2.1 焊接试样外观图 17
3.2.2 试样剪切力学性能试验及分析 21
3.2.3焊接试样金相分析 25
3.3 关于铝合金7A52螺柱焊的设想和看法 27
结 论 29
致 谢 30
参考文献 31
1 绪论
1.1 螺柱焊
上一篇：废旧氨纶改性生物沥青研究
下一篇：铝复合材料熔焊工艺试验与性能分析