摘要对于信号发生器产生的高频率、低电平的信号来说,需要用分立元件将其放大,使得接收器能够接受到信号。为了搭建一个合理并且可以实际运用的放大电路,先去查阅资料和书籍,了解过往的类似解决问题的方法和思路。然后,我需要充分了解分立元件的工作原理并设计出一套可行的方案。并计算其静态工作点确保其在放大倍数稳定的范围内放大信号。然后将计算并仿真成功完成的电路按原理图搭建出来,在实验室进行观察、统计和测试并记录电路板的状况和所遇到的问题。反馈问题后分析问题的成因,然后提出解决方案,并在此实验,通过示波器显示的波形有无失真和噪声来判断实验的结果是否符合要求。最后总结整个实验过程的经验和体会,如果有需要再进行更深入的分析和思考。28670
关键词    小信号     放大     电路  三极管     场效应管    元器件
毕业论文设计说明书外文摘要
Title     The amplification of High-frequency signal Which has a  Small range           
Abstract
    For high frequency signal generator, a low level signal, the need to enlarge discrete components, so that the receiver can receive the signal. In order to build a reasonable and practical application of the amplifier circuit can, go to the access to information and books, learn how to solve problems similar to the past and ideas. Then, I need to fully understand the working principle of discrete components and design a viable option. And calculate the quiescent operating point to ensure its zoom magnification within a stable range of the signal.Then calculate and simulate successfully completed build out circuit according to the schematic in the laboratory observation, statistics and test and document the status of the circuit board and the problems encountered. After analyzing the causes of the problem of feedback problems, and then propose a solution, and in this experiment, whether the distortion and noise waveform display via an oscilloscope to determine whether compliance with the requirements of the experimental results.Finally, lessons learned and experience throughout the experiment, and if there is need to carry out more in-depth analysis and reflection.
Keywords    amplified    signal    electronics
            Circuit      sophisticated   signal
目   次
1  绪论    1
1.1  小信号    1
1.2  放大电路的应用及背景    1
2  mos管放大电路的设计    1
2.1  mos管工作原理    2
2.2  mos管的组态选择    3
2.3  mos管的型号选择    6
2.4  mos管放大电路的设计    6
2.5  mos管放大电路的参数选择    10
2.6  mos管放大电路的仿真与调试    14
2.7  mos管放大电路实际搭建和测试    19
2.8  mos管放大电路的设计心得与体会    20
3  三极管放大电路的设计    21
3.1  三极管的工作原理    21
3.2  三极管的组态和型号选择    22
3.3  三极管的放大电路设计    25
3.4  三极管的放大电路参数选择    27
3.5  三极管放大电路的仿真与调试    29
3.6  三极管放大电路的实际搭建与测试    31
上一篇:复杂背景条件下红外目标背景抑制方法研究
下一篇:OPNET基于CAN总线的列车通信网络设计

基于LBG算法的语音信号的矢量量化方法设计

STC89C51单片机的AD9850的高频信号源设计+电路图

Multisim高频放大器的设计

MATLAB线性调频信号的检测和估计+程序

STFT钢琴音乐信号的检测技术研究

AD8309高频对数放大器的设计+PCB电路图

多相码信号的分析与处理

浅谈传统人文精神茬大學...

拉力采集上位机软件开发任务书

多元化刑事简易程序构建探讨【9365字】

《醉青春》导演作品阐述

国内外无刷直流电动机研究现状

谷度酒庄消费者回访调查问卷表

浅谈新形势下妇产科护理...

中国古代秘书擅权的发展和恶变

辩护律师的作证义务和保...

高校网球场馆运营管理初探【1805字】